Waterproof Individually Addressable RGB Neon Pixel Ws2812b LED Strip for Bar TV Music Festival

Basic Info

Model NO.	STB-WS2812B-3PIN-RGB
Power Consumti	18/43 W/M
LED Qty	60/144
Warranty	5 Years
Operating Temperature	-20° C to 50° C
Storage Temperature	-40° C to 70° C
Width	10/20 mm
Transport Package	Neutral Packaging
Specification	5000*10/12
Trademark	Suntech
Origin	China
HS Code	9405429000
Production Capacity	1000000

Product Description

Product Description
1.IC control circuit and LED point light source share a power source.2.The control circuit is integrated with the RGB chip in a 5050 package component, constituting a complete external control pixel point.3.Built-in signal shaping circuit, any pixel after receiving the signal after waveform shaping output, to ensure that the line waveform distortion will not accumulate.4.Built-in power-on reset and power-off reset circuit.5.The three primary colors of each pixel can achieve 256 levels of brightness display, complete 16777216 colors full true color display.6.Port scanning frequency 2KHz/s.7.Serial cascade connector, through a signal line to complete data reception and decoding.8.No need to add any circuit when the transmission distance of any two points does not exceed 5 meters.9.When the refresh rate is 30 frames per second, the number of cascades is not less than 1024 points.10.Data transmission speed up to 800Kbps.11.The color of light is highly consistent, cost-effective.

 

product parameters:

Product Dimension:Production Application:

Control Diagram and Installation Diagram:
1. Madrix control
Recommended controller: T790K, YC3000

2.Online control by computer
Recommended controller: T-790K

Installation Notes(1)Please read the manual in detail before installation.
(2)Before installation, make sure that the working voltage of the LED meteor tube light matches the output
voltage of the switching power supply you purchased.
(3)When installing, pay attention to the wiring label of the lamp. The red wire is connected to "positive (+)",
the black wire is connected to "negative (-)", and other colors are detailed on the wiring label of the lamp. The
wiring must be powered off during installation.
(4)It is strictly forbidden to cut off the male and female head wires with electricity, so as not to burn out the
lamps in the short-circuit.
(5)LED meteor tube light with control must comply with the male in and female out, and the direction of the
signal must be connected in series when connecting the lamps.
(6)This lamp is forbidden to be disassembled without permission, if it is disassembled without permission, our
company will not bear the warrantySimple troubleshooting
(1)When the lamp does not turn on when it is powered on: check whether the switching power supply has a
working output voltage, or whether the working voltage of the switching power supply is normal.
(2)After the switch power supply works normally, the lamp still does not light up: check whether the signal line
of the lamp is connected incorrectly or whether the connection is normal, and check whether the controller
works normally and whether it has been powered on.
(3)The above work is normal, but the lamp still does not light up: check whether the SD card of the controller
has been inserted, and whether there is a program in the SD card.
(4)The lamp jumps or flickers: Check whether the negative pole of the lamp is connected in parallel with the
negative pole of the switching power supply including the GND of the controller. (5)If the above inspection is completed, it is still out of control, please contact our sales staff to deal with it.
Advantages of Shenzhen Suntech LED strip 1. LED strip PCB thickness: The thickness of led strip below 60leds is about 0.25mm, (for example:30leds/m, 60leds/m)The thickness of the led strip above 60leds is about 0.35mm (for example: 90leds/m, 120leds/m, 144leds/m). The thickness of the general PCB on the market is 0.2mm. The thickness of the copper used in the PCB board --- the thicker the copper the more current can flow and the more efficient the strip is.
Suntech company's 12v is connected to 5m led strip, 24v is connected to 10m led strip, the voltage drop is very small, almost no voltage drop.

2. Resistance : Authentic Guarantee, Antioxidant. Resistance SMD1.2mm*0.6mm,Heat dissipation is good, high temperature resistance and very stable.
3. Capacitance: Double Capacitor Design,one is filter capacitor, one is current limiter. Dual capacitor design can protect the IC, and the signal transmission is stable.If you touch the capacitor with your hands, it will not burn out, and it will not burn out if the positive and negative poles are reversed in a short period of time.
Please see the picture below, the difference between the 12v WS2818 produced by Suntech company and other companies.
Please see the picture below, this is the function of each component:4. Led strip connection:Tin is added to the connection of the light strip, which is convenient for welding after cutting. The solder joints are full, and there will be no false welding.5. LED brand: Epistar, RGB lamp bead brightness up to about 2700mcd. The approximate brightness achieved on the market is 2000mcd.
6. Back side of PCB board:There is a line mark design on the back of the PCB board, and the light strip is inserted into the neon tube for easy cutting.7. Wire: Cold resistance, high temperature resistance (below 105 degrees), flame retardant, Anti-uv. All products of Suntech Company will have two more wires, which are specially used for power supply.For IP67 waterproof LED Strip, Suntech will make the wire longer (about 1cm) at the connector, This prevents water from seeping in, and even if water seeps into the edge of the LED strip, it is not easily damaged.8. Adhesive: Genuine 3M LSE, will not fall off As can be seen from the picture below, the genuine 3M LSE is transparent under the light, It is enough to prove that the stickiness is very strong. On the contrary, use inferior 3M LSE, the led strip will not 9. Connector: The cores of Suntech connectors are all solid core pins, and some companies may use hollow pins. Please see the comparison chart below: